Daktronics Remote Control System RC-100 Manual do Utilizador

Remote Control System RC-100 DataMaster Operation Manual ED-15576 Rev 3 – 26 September 2012 201 Daktronics Drive PO Box 5128 Brookings, SD 57006

RC-100 System Overview 5 Section 2: RC-100 System Overview The RC-100 system allows wireless control of multiple display applications. This system

RC-100 Base Station 7 Section 3: RC-100 Base Station The RC-100 wireless Base Station is used to communicate with all RC-100 wireless handheld con

8 RC-100 Base Station Selecting Functions Refer to Figure 5 for the wireless Base Station circuit board assembly drawing. To access the circuit b

RC-100 Base Station 9 3.2 Channel Setting The wireless Base Station and wireless handheld device use internal radio modules to communicate. The ra

10 RC-100 Base Station 3.3 Synchronizing Multiple Base Stations and Channel Selection If two or more server Base Stations need to operate at the s

RC-100 Base Station 11 3.4 Server/Client Mode Setting The RC-100 wireless Base Station can operate in either Server Mode or Client Mode, depending

12 RC-100 Base Station 3.5 Wireless Base Station LEDs The wireless Base Station circuit board includes several light-emitting diodes (LEDs) for di

RC-100 Base Station 13 5 CAN TX Green This LED flashes when Controller Area Network (CAN) data is transmitted to a connected device. 6 CAN RX Red T

RC-100 Handheld Controller 15 Section 4: RC-100 Handheld Controller 4.1 Powering the Controller On and Off Using the Keypad  Press and hold th

16 RC-100 Handheld Controller 4.4 Operation Modes The RC-100 wireless handheld controller (Figure 2) always operates in one of two modes: Config

RC-100 Handheld Controller 17 Setting Power Save Mode Display Action Press <ENTER> to modify the default LCD power on when idle time. Thi

18 RC-100 Handheld Controller Signal Strength Indicator Once a connection has been made, the top line of the LCD will show the signal strength (Fig

RC-100 Handheld Controller 19 3 Up/Down Arrows These keys are used to navigate through menu choices and make certain selections. Arrows may also be

DataMaster Applications 21 Section 5: DataMaster Applications This section provides information about the “DataMaster” function of the RC-100 wire

22 DataMaster Applications 5.2 DataMaster Application Keys All DataMaster applications have keys with the same functionality, as described below.

DataMaster Applications 23 Automatic If AUTOMATIC dimming is selected, the following will be shown on the LCD: Display Action Press <ENTER>

ED-15576 Product 1279-99 Rev 3 – 26 September 2012 DAKTRONICS, INC. Copyright  2005-2012 All rights reserved. Whil

24 DataMaster Applications Display Sequence As values are edited, they do not instantly appear on the display. To send a new sequence to the displa

DataMaster Applications 25 LED Test Select LED TEST to test the LED digits on the display. Display Action Press <ENTER> to cycle the displ

26 DataMaster Applications Display Option 1-5 (Lottery Displays Only) Select a DISPLAY OPTION to set the position of the decimal for each lottery d

DataMaster Applications 27 Display Passcode This setting is only available after entering the Display Status menu option. Display Action While t

28 DataMaster Applications Display Action N= number of clients The LCD will show how many clients are found. If the <YES> key is presse

Gas Price Operation 29 Section 6: Gas Price Operation Insert: LL-2617 The insert drawing is located in Appendix A. If an insert is lost or damage

30 Gas Price Operation If the decimal point appears in the wrong spot on the LCD: 1. Press <MENU>. 2. Use the arrow keys <↑↓> to sel

Rate Display Operation 31 Section 7: Rate Display Operation Insert: LL-2617 The insert drawing is located in Appendix A. If an insert is lost or

Lottery Display Operation 33 Section 8: Lottery Display Operation Insert: LL-2617 The insert drawing is located in Appendix A. If an insert i

Troubleshooting 35 Section 9: Troubleshooting 9.1 Handheld Controller Error Messages Display Cause/Solution NN = current setting The wir

36 Troubleshooting Display Cause/Solution The Base Station has stopped responding to the wireless handheld. This could mean any of the follo

Troubleshooting 37 9.3 Replacing Handheld Battery To verify the battery is replaceable, look at the revision number on the back of the unit (Figur

Reference Drawings 39 Appendix A: Reference Drawings Drawing Title Drawing Number Insert, LL-2617 RC-100 Price Displays ...

THE CONCEPTS EXPRESSED AND DETAILS SHOWN ON THISDRAWING ARE CONFIDENTIAL AND PROPRIETARY. DO NOTREPRODUCE BY ANY MEANS WITHOUT THE EXPRESSEDWRITTEN

Table of Contents i Table of Contents Section 1: Introduction ...

Daktronics Warranty and Limitation of Liability 41 Appendix B: Daktronics Warranty and Limitation of Liability

Copyright © Daktronics, Inc. SL-02374 Rev 10 02-Mar-2009 Page 1 of 2 DAKTRONICSWARRANTY AND LIMITATION OF LIABILITY This Warranty and Limi

Copyright © Daktronics, Inc. SL-02374 Rev 10 02-Mar-2009 Page 2 of 2 C. Damage caused by the failure to provide a continuously suitable en

ii Table of Contents Display Sequence ...

Introduction 1 Section 1: Introduction This manual is designed to explain the operation of the Daktronics RC-100 Remote Control System for DataMas

2 Introduction 1.2 Daktronics Exchange and Repair & Return Programs Exchange Program The Daktronics Exchange Program is a quick, economical se

Introduction 3 Repair & Return Program For items not subject to exchange, Daktronics offers a Repair & Return Program. To send a part for r